DiChem Formease CRA2 - Chemical Release Agent

BCA(C & CA) Category 5.

Reactive, drying type CRA. Formease CRA2 is a fast drying type chemical release agent formulated to give easy release of formwork and quality surface finishes to concrete. Suitable for use on all types of formwork and is the preferred type of product on proprietary MDO & HDO plywood forms and steel shutters. Spray applied.

Coverage:- 15 - 60m²/ltr.

DiChem Chemstrike MRO - Mould Oil

BCA (C & CA) Category 2

A versatile specially blended mould oil, suitable on most formwork types. Gives optimum release and finish on a wide range of mix designs. Spray or brush applied.

Coverage:- 15 - 45m²/ltr.

Nufins Chemlease - Chemical Release Agent

BCA(C & CA) Category 5.  - WRAS APPROVED MATERIAL

A formulation of hydrocarbon carrier and chemically active ingredient producing a low viscosity concrete mould release agent suitable for use on “good one side” shuttering ply, MDO, timber, steel, or shutter faces. It is applied by spray or brush prior to concrete casting to achieve a clean “strike”.

Coverage:- 30 - 50m²/ltr.

INFORMATION APPLICATION

EQUIPMENT

Back to Products

Home

Next Page

Previous Page

DiChem Formease CRA1 - Chemical Release Agent

BCA(C & CA) Category 5.

Reactive, drying type CRA. Formease CRA1 is a slow drying type chemical release agent formulated to give easy release of formwork and quality surface finishes to concrete. Suitable for use on all types of formwork and is the preferred type of product on proprietary MDO & HDO plywood forms and steel shutters, it can also be used on sealed timber forms. Spray applied. Low Hazard.

Coverage:- 15 - 60m²/ltr.

DiChem FORMSTRIP - Chemical Release Agent

BCA(C & CA) Category 5.

A non Flammable formulation of hydrocarbon carrier and chemically active ingredient producing a low viscosity concrete mould release agent suitable for use on “good one side” shuttering ply, MDO, timber, steel, or shutter faces. It is applied by spray or brush prior to concrete casting to achieve a clean “strike” .

Coverage:- 30 - 50m²/ltr.

Adomast Extracon XS - Chemical Release Agent

BCA (C & CA) Category 5.

Reactive, drying type CRA. Recommended for use on MDO, HDO, phenolic and polyurethane coated plyforms, steel forms etc. Spray applied.

Coverage:- 25 - 60m²/ltr.

Adomast Extracon DS - Chemical Release Agent

BCA(C & CA) Category 5.

Reactive CRA for general use but specifically developed for use on plastic moulds and flexible liners to ensure extended form ‘life’ and architectural quality of finished product. Spray applied. Coverage:- 25 - 60m²/ltr.

Norsekem Thorcast - Mould Oil

BCA (C & CA) Category 2

A highly versatile specially blended quality neat oil with surfactant, suitable on most formwork types. Gives optimum release and quality finish over a wide range of mix designs. Spray or brush applied.

Coverage:- 20 - 45m²/ltr.

Pieri Cire LM 33 - Solid Release Wax

Pieri LM33 is a paste release wax for high quality architectural concrete surfaces. Suitable on all formwork materials. Provides exceptional release on difficult pieces eg, Fluting, caissons etc. Also highly recommended for top down construction, concrete counter casting, release can be achieved even after a years contact together .

Coverage:- up to 120 m²/kg

Pieri Cire E 31 -  Release Wax -

Solvent based sprayable release wax for high quality architectural concrete surfaces, Suitable for use on clean steel or sealed wood forms, however not suitable for concrete counter casting. A drying time of about 15 minutes is recommended before pouring. Coverage:- 20-25 m²/ltr.

Pieri Decobio 310 -  Formerly Decobio S31 / S32

A vegetable oil based release agent specifically designed to solve release and health risk problems on site and in pre-cast factories. Can be used on all types of mould or formwork material, and is recommended for general and high quality finishes. Spray applied using a cone nozzle or a very fine fan nozzle. Coverage:- 40-50 m²/ltr.

GUIDE TO RELEASE 

SYSTEM  SELECTION

BASF Masterfinish RL211 - Chemical Release Agent

A water emulsion based on non-toxic, non-irritant, vegetable oils. It is readily biodegradable to OECD Guideline 301. Specially formulated to give an easy and complete release of the concrete from the forms and a significantly improved quality of the concrete surface which is smooth, homogeneous and free of pinholes. Spray applied. Formerly Rheofinish R211

Coverage:- 30 - 100m²/ltr.

DATA SHEET

SAFETY DATA

Pieri Decobio 410 -  Formerly Decobio VS43

A Solvent free vegetable and synthetic oil based release agent specifically designed to solve release and health risk problems on site and in pre-cast factories. Can be used on all types of mould or formwork material, and is recommended for general and high quality finishes. Spray applied using a cone nozzle or a very fine fan nozzle. Coverage:- 40-50 m²/ltr.

Back to Products

Home

Next Page

Previous Page

We can supply all of the equipment you need to apply your products here

We are also able to source the following products should they be required for your project. Nufins Chemlease, Nufins Formstrike, Nufins Nulease, Fosroc Demolux, Fosroc Demokret, Sika Separol G, Sika Separol S, Adomast Adolease, Adomast Adostrike, Adomast Adostrip, Adomast Safelease,  BASF Masterfinish MPT299, BASF Masterfinish FW323, Adomast Extracon DS, Adomast Extracon XS

Direct Chemicals are suppliers and manufacturers of Formwork Chemicals, Concrete Mould Oil, Mould Oil, Release Wax, Chemical Release Agent, Releasing agent, mold oil, cheap mould oil, form oil,  Formease CRA1, Plyease, Formstrip, Formease CRA2, Chemstrike MRO, Rheofinish 211, Extracon XS, Extracon DS, Extrastrike 402S, Plastrip S, Naturol 2, Ecodin WB, Teknistrip, Pieri  Decobio 410, Pieri Decobio 310 , Pieri Decobio 320, Pieri Cire E-31, Pieri Cire LM-33, Bioidegradeable and environmentally friendly release products using vegetable oils and water based products

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

DATA SHEET

SAFETY DATA

Norsekem Teknistrip -  Chemical Release Agent

BCA(C & CA) Category 5.

Teknistrip is a chemical release agent formulated to give easy release of moulds and quality surface finishes to concrete. Teknistrip is formulated for use with plastic and thermo plastic mould liners (Polypropylene, ABS, Polyurethane, some latex and rubber moulds) commonly used in pre-cast manufacture of paving slabs, ornaments, edgings etc. Can also be used on steel and most other form materials. Due to its Non-Flammable and Non-Harmfull label this product is the preferred release agent in enclosed environments such as pre-cast factories, tunnels and basements.  Coverage:- 25-60 m²/ltr.

DATA SHEET

SAFETY DATA

Norsekem Ecodin WB - Emulsion Release Agent

A water borne Chemical Release Agent based on modern rapeseed ester emulsion technology. Supplied ready for use and best applied by spraying techniques. It is completely free from hydrocarbon solvents and is therefore VOC free. This makes it ideal for use in  pre-cast factories or confined areas where the solvent vapours of traditional release agents would be a hazard to the work force. ECODIN WB has been designed to give easy release of formwork and produce high quality surface finishes with all types of concrete in both Pre-cast and In-Situ concrete. Coverage:- 25-60 m²/ltr.

DATA SHEET

SAFETY DATA

Norsekem Teknicon - Chemical Release Agent

BCA(C & CA) Category 5.

Reactive type high quality Chemical Release Agent that is low hazard and is not regulated for road transport. Suitable for general use on most formwork materials. Particularly recommended by Timber Suppliers and Associations as the preferred type of product on proprietary MDO & HDO plywood forms. Is also ideal for use on steel shutters and column boxes and sealed timber forms. Spray applied. Non flammable. Coverage: 25 - 60m²/ltr

DATA SHEET

SAFETY DATA

Norsekem Teknicast

A chemically neutral sprayable liquid release wax. Particularly recommended for architectural concrete production in pre-cast factories, as well as difficult release situations on site. Suitable for use on GRP, Plastic, and Phenolic boards. Is also ideal for use on steel shutters, column boxes and sealed timber forms. Spray applied. Coverage: 30m²/ltr

DATA SHEET

SAFETY DATA

Norsekem Ecodin RS+

ECODIN RS+ is a readily biodegradable chemical release agent specially formulated to give easy release from pre-cast moulds or formwork and provides a high quality surface finish to concrete. The low hazard formulation makes it ideal for use in Pre-Cast Factories The product utilizes sustainable Vegetable Oils within its formulation. Spray applied.

Coverage : 25 - 60m²/ltr

DATA SHEET

SAFETY DATA